D52-BS53

This linear rail is supplied in aluminium. The length is adaptable to the needs of the user. The rail length is adjusted to demand up to 2500mm (limit due to transportation requirements). Standard rail lengths are 500, 1000, 1500 and 2000 mm. Other lengths are possible. The standard rails are delivered undrilled, but they can be produced according to a specific hole pattern. The recommended drilling pattern is shown on the technical data sheet. Each Rail is provided with two end-stop crosspins. These reduce the possible movement by 11mm at each end.


    Option

    Pictures


    3D


    Option :

    Description

    This linear rail is supplied in aluminium. The length is adaptable to the needs of the user. The rail length is adjusted to demand up to 2500mm (limit due to transportation requirements). Standard rail lengths are 500, 1000, 1500 and 2000 mm. Other lengths are possible.[CR]] The standard rails are delivered undrilled, but they can be produced according to a specific hole pattern. The recommended drilling pattern is shown on the technical data sheet.[CR]] Each Rail is provided with two end-stop crosspins. These reduce the possible movement by 11mm at each end.

    Runner BP53 has 3 steel plastic coated rollers mounted on a stainless steel plate. Runner BS53 has 3 stainless steel rollers mounted on a stainless steel plate. The central roller is eccentrically adjustable on its axel. A mark on the body of the runner indicates the correct orientation of the rollers relative to the load. The coated rollers provide a particularly silent movement. They are lubricated for life and are waterproof (IP54). Its overall length is 138mm and it includes 2 M6 threaded holes at 100mm centres. Each runner is fitted with plastic wipers at each end that clear the raceway as it moves ensuring a smooth motion. Each runner could be mounted in either the aluminium rail (D52), zinc plated steel (E53) or stainless steel (ST53) according to the environmental requirements of each application.

    Each runner has a load capacity. Increasing the number of runners increases the load capacity by the same factor.

    Applications

    This linear rail is designed for medium loads in applications requiring a very small footprint, such as covers or enclosures for guard of small machine.

    Recommended operating temperatures from -20 to 100°C.

    Installing these guides in applications with severe vibrations is not recommended: indentation of profiles by ball bearings might occure. Do not hesitate to contact us.

    This kind of product will not slide well under torque; please ensure that the load is balanced on one or more runners, if necessary.

    This product can be used as a sliding pair, guide bar or rod, suspended rail, handling rail, sliding doors horizontal slider or vertical guide.

    Manufacture

    Chambrelans production of this guide rail is based on the use of extruded aluminum profiles.

    Anti-corrosion standard coating for the rail is soft anodisation.

    The rail has axial pins covered with rubber at each end.

    Adjusting the runners. Runners are delivered as fully assembled items, mounted with pre-set running properties. If a runner is delivered separately, or if it should be mounted in another rail, or if you have non-standard operating requirements, an adjustment can be made; Note that a good adjustment affects the lifetime of the assembly. - After checking the cleanliness of the raceways, introduce the runner without the scrapers into the rail, - Loosen the set screw of the central roller which is eccentrically mounted. - With the rail on the major axis, rotate the provided key to obtain the desired setting, and then tighten the mounting screw to the recommended torque on the data sheet, - Check the sliding of the runner into the rail; It must be moved freely without excessive play, - Replace the wipers.

    Chambrelan is specialized in the design and manufacturing of telescopic slides and rails for industrial applications: reinforced slides, linear slide bearings rail, bearings guide, steel, aluminum or stainless steel sliders, partial, full or over extension, heavy duty industrial drawers...

    Greasings

    • Standard slides are delivered slightly greased. We use a high pressure bearing grease for steel slides and a white grease for aluminum and stainless slides. Upon request, we can use food grease (compatible clean room) a high temperature grease a teflon free grease (for spray booths...) grease free mounting (although we do not advise this option)

    Options

    Manual lock

    It has no lock option so far.

    Surface treatment

    This slide can be supplied with a hard anodization coating, which offers, in addition to corrosion resistance, an increased resistance to hammering of ball bearings. This option can be usefull in the case of applications subject to vibrations.

    high temp use
    • We do not recommend using this product outside the standard temperature range.
    Vertical mounting

    This slide can be mounted vertically (guillotine).

    Drilling scheme

    Download

    Standard closed lengths

    The characteristics given on this website correspond to standard manufacture or usual requirements. Our position as a manufacturer enables us to offer great flexibility in order to meet the most specific requirements.

    MeasuresLoadsRail
    length
    Number
    of runners
    Load per carrier
    on major axis
    Load per carrier
    on minor axis
    StockPlease select
    Length
    0
    Runners
    3
    Load per carrier on minor axis

    Load per carrier on major axis
    03instock
    Length
    0
    Runners
    2
    Load per carrier on minor axis

    Load per carrier on major axis
    02instock
    Length
    0
    Runners
    1
    Load per carrier on minor axis

    Load per carrier on major axis
    01instock

    A question?

    Contact us for more information

    Copyright 2017 CHAMBRELAN - Legal terms - Sitemap